Da ja isto imam toga.
Meni radi show od pocetka,samo je bitno pogodit kolicinu vate
Ja odrezem malo preko ruba dimnjaka,natopim vatu,i onda samo mrvu vate spustim u kanalice.
Bitno jer na ovoj verziji je siri dimnjak nego inace a kanalici su dosta uski.
I ako se stavi previse vate onaj valjak od dimnjaka je stisne i nema protoka,pri tom se javlja zagorenost.

_________________
Evic,Nemesis clone,Stingray clone,CHI YOU clone,Spinner 1300mAh,Protank 2,Mini Protank 2,Evod,AGA T2,RSST,IGO-L,Trident,Russian 91%,Fogger v4,3D Dripper,Origen,Origen v2,Magma,Stillare,Quasar,Brass monkey

Možda je prikladno da pitam ovdje... Kakvo je vaše mišljenje o ovom pvd coatingu unutar atomizera? Ameri su digli paniku jer je u doticaju sa tekućinom. Meni je to prenapuhano, jer je to prilično tvrd i postojan sloj ali opreza nikad dosta? Gledam trenutno kayfun lite v2 black...

_________________
Klon od klona.

dok su pušili nisu se pitali šta sve sadrži cigareta, meni isto taj premaz djeluje vrlo tvrdo i neutralno

_________________
There's a fine line between fishing and just standing on the shore like an idiot. ><((((º>-------------------------------------------



Modovi, akrilni stalci i 3D printanje

nisam bas za to

The most common polymers used are polyester, polyurethane, polyester-epoxy (known as hybrid), straight epoxy (fusion bonded epoxy) and acrylics.

edit: Chemical pre-treatments involve the use of phosphates or chromates in submersion or spray application. These often occur in multiple stages and consist of degreasing, etching, de-smutting, various rinses and the final phosphating or chromating of the substrate. The pre-treatment process both cleans and improves bonding of the powder to the metal. Recent additional processes have been developed that avoid the use of chromates, as these can be toxic to the environment. Titanium zirconium and silanes offer similar performance against corrosion and adhesion of the powder.


citaj dalje na: http://en.wikipedia.org/wiki/Powder_coating

_________________
Ako te uhvati napadaj radinosti, mirno sjedni u ćošak i čekaj da te napadaji prođu!

Top III :Habana, Grandmaster, Grenada
I² Element18350/18650+kick, Ant-i-Mod +5V, Ergo69-Yenki69,UD Agi,IgoW

Jel kome procuri na driptipu prilikom punjenja?

_________________


Glup si ko Karamarko
http://goo.gl/A9lj9A

Previše si ga ili prenaglo nadrukao, ja ga punim odozgo i samo pridržavam stakleni tank da se ne mrda, onda nema problema.

_________________
There's a fine line between fishing and just standing on the shore like an idiot. ><((((º>-------------------------------------------



Modovi, akrilni stalci i 3D printanje

prenaglo. ma pocet cu i ja cesce naljevati odozgo. blazena kaja sto se tice toga

_________________


Glup si ko Karamarko
http://goo.gl/A9lj9A

Ah, vidim, nema napretka kod Fogija po tom pitanju...nista od nabavke onda

_________________
http://journey-liquids.com
mod: VT200,VTC mini, Elitar,Mini volt,Paps v4, SMPL v2, Vapor Giant, Nemesis, Dimitri,IPV5
Atty: Fogger v2, Kayfun lite v2+, Nextiny, YEP v2, Origen little,FEV v2, Taifun GT,GS i GLS, Fogger mini,
Aromamizer, Ithaka,Oddy, Kayfun mini v2.1,UTA II, Vapor Giant

Haha,bas si me dobro nasmijao:D

_________________

zasto?

_________________


Glup si ko Karamarko
http://goo.gl/A9lj9A